So far Smoant have created plenty of Knight products including The Knight 40 & 80 pod kits, plus the Knight V1 SBS mod.

More Details On The Smoant Knight Q…

This is a funky looking pod kit which is apparently inspired by a “Four Leaf Clover”.

Which according to Smoant is…

“a symbol of wonderful fortune and permanent companionship”

Awww sooo cute!

This has a 1000mAh internal battery which is charged at a 1A charge rate using the USB Type C port.

The output is not specified but you need not worry about it as the ANT chip will set the output automatically to suit the coil installed.

An LED indicator is provided to inform you of the battery and device status.

This uses replaceable Mesh coils which are the “P” range which are also compatible with the Pasito Mini. You get the P-1 0.6ohm coil and P-2 0.8ohm coil included in the kit. There is also a 1ohm coil available separately.

The pod will hold up to 3ml of your own e-liquid via the side fill port.

On the base of the pod is an airflow control to tailor the incoming air resistance to suit your vaping style.

Here is an introduction video from the Smoant YouTube channel.

There are 5 colours to choose from: Sakura Pink, Space Grey, Purple Haze, Gunmetal and Fiery Red.

Kit Includes

• Smoant Knight Q device
• P-1 0.6ohm coil (installed)
• P-2 0.8ohm coil
• Lanyard
• USB Type C cable
• User manual

Smoant Knight Q Specs

• Size: 60x50x16.8mm
• Battery: 1000mAh (internal)
• Display: LED indicator
• Output: Automatically selects the correct output
• Type C USB charging – 1A charge rate – 45-50 minute charge time
• Resistance range: Not specified
• Capacity: 3ml
• Coils: P Series Smoant Coils compatible
• Adjustable airflow
• Side fill
• AI Smart Ant-Chip

I think the design looks comfortable to hold and there is plenty of tech in there to keep most vapers happy!

What do you think of the Smoant Knight Q? Let me know in the comments below!

The post Smoant Knight Q Preview – Lucky Clover? appeared first on Ecigclick.

Smoant have been in the vape business for a long time bringing us vape gear such as the Pasito pod kits, Knight range and various Battlestar branded devices.

What To Expect From The Smoant Levin…

The Smoant Levin is designed to be a simple to use pod kit.

The main device has a 1000mAh battery which is charged in 45-60 minutes at a 1A charge rate via the USB Type C port.

Output wise this is specified as 5-30W but the Ant Chip inside the device selects the correct output for the pod installed – no adjustment required.

You get an airflow adjustment slider to choose your preferred incoming air volume.

Also some of the pod area is on display to view your e-liquid level.

A smart multicolour LED indicator is provided to show your battery charge level and any faults that occur.

A new range of Levin pods have been created which are refillable by removing the mouthpiece to reveal the fill port.

There are 3 pod options, each with a Mesh coil – 0.6ohm, 0.8ohm and 1ohm, sadly the website does not tell you which of these you get in the kit.

The pods will hold up to 2ml of your own e-liquid but are disposable when the coil performance has deteriorated. This is easier than replacing coils but not as wasteful as a disposable device as you only discard the pod component.

Here is a brief introduction video from the Smoant YouTube channel.

There are 5 colour options to choose from: Kelly Green, Space Grey, Sky Blue, Royal Purple and Pinky Blue.

Kit Includes

• Smoant Levin device
• Lanyard
• USB Type C cable
• User manual

Smoant Levin Specs

• Size: 99.4x25x15mm
• Battery: 1000mAh (internal)
• Material: Space Aluminium
• Display: LED indicator
• Output: 5-30W – automatically selects output for coil resistance
• Type C USB charging – 1A charge rate – 45-60 min charge time
• Resistance range:  Not specified
• Capacity: 2ml
• Pods: Fixed Mesh coil, refillable Levin Pods – 0.6ohm, 0.8ohm, 1ohm
• Adjustable airflow
• Top fill
• AI Smart Ant Chip

I do like the design and materials from the marketing images!

Let me know what you think of the Smoant Levin in the comments below!

The post Smoant Levin Preview – ♫♪ “Don’t Stop Be-Levin” ♫♪ appeared first on Ecigclick.

The Pasito family of pod kits include the original Pasito and the Pasito II.

What To Expect From The Smoant Pasito Mini…

I actually reviewed the original Pasito and the fact it had an RBA coil which gave out amazing flavour really set it apart from other pod kits at the time.

Unfortunately from what I can tell (I may be wrong) but this version is not compatible with previous Pasito coils.

There appears to be a new coil range the “P-Series” which come in 0.6ohm (P-1), 0.8ohm (P-2) and 1ohm (P-3) mesh coils. The P-1 and P-3 coils are included in the kit.

Inside the mod is a 1100mAh battery which is charged via the USB Type C port at up to 1A charge rate.

This has 3 power output levels which depend on which coil is installed…

• High = 22.2W (0.6ohm coil), 16.6W (0.8ohm coil) or 13.3W (1ohm coil)
• Medium = 21W (0.6ohm), 15.7W (0.8ohm) or 12.6W (1 ohm)
• Low = 20W (0.6ohm), 15W (0.8ohm) or 11.9W (1ohm).

The output is regulated so should stay constant regardless of battery charge.

A strip light style LED will inform of the power level selected and the battery charge remaining.

The pod section has an adjustable airflow slider to tailor the incoming airflow restriction to suit your preference.

Plus to make filling easy a side fill port is provided so you no longer have to remove the pod when filling!

Talking of filling this will hold up to 3.5ml of your own e-liquid in standard format. However for marketing in TPD Regulated areas the capacity will be reduced to 2ml.

A clear viewing window allows you to see your e-liquid level easily.

Here is a brief introduction video from the Smoant YouTube channel.

There are 8 colours to choose from: Space Grey, Brown, Black, Blue Twill, Cyan Gradient, Kelly Green, White and limited edition Seashell.

Kit Includes

• Smoant Pasito Mini device
• Pod cartridge
• 0.6ohm P-1 coil (installed)
• 1ohm P-3 coil
• USB Type C cable
• User manual

Smoant Pasito Mini Specs

• Size: 97x36x16.5mm
• Output: 5-30W
• Mode: 3 output levels
• Battery: 1100mAh (internal)
• Display: LED indicator
• Resistance range: 0.4-3ohm
• USB Type C port – 1A charge rate
• Pods: Refillable, replaceable coils
• Compatibility – compatible with Smoant P series coils
• Capacity: 3.5ml (Standard) / 2ml (TPD)
• Side fill
• Adjustable airflow
• AI Smart Ant-chip

This looks stunning, but I am sad there appears to be no RBA option which was the best feature of the original.

Anyway let me know what you think of the Smoant Pasito Mini kit in the comments below!

The post Smoant Pasito Mini Preview – Guess Who’s Back! appeared first on Ecigclick.

SMOANT are no stranger when it comes to pod kits. The Pasito, Battlestar and Charon ranges instantly spring to mind. I was blissfully unaware there’s already been a KNIGHT 80 pod kit released.

The SMOANT KNIGHT 40 treads a completely different path in terms of power and design.

I’ve already mentioned this in recent reviews – the trend these days is for futuristic, high tech transparency. We’ve seen it with the Voopoo P1 pod kit and the Vaporesso LUXE XR.

.. We’re seeing it again with the KNIGHT 40 pod kit.

SMOANT are based in Shenzhen, China. Their continuous goal is to satisfy all types of vapers. Yes, that does include tootle puffers and Mod wompers!

They’re also open to any possible improvements to their products. I’m hoping that’s not necessary with the KNIGHT 40 pod kit. Seems SMOANT aren’t happy until we are.

What Can We Expect From the SMOANT KNIGHT 40 Pod Kit?

Gone is the single 18650 battery of the KNIGHT 80 pod kit, ditched in favour of an integrated 1500mAh alternative.

The screen is now front mounted and the box style design wouldn’t look out of place in an upcoming Robocop flick.

We now only have 40W to play about with. To work around the coil configurations of its more powerful sibling, three of the plug and play S series mesh coils have been upgraded.

A coil adaptor is included to ensure full compatibility with the rest of the S-Series coils.

Thanks to top adjustable airflow, the SMOANT KNIGHT 40 is able to capitalise on the upgraded coils to provide either a DL (Direct Lung), RDL (Restrictive Direct Lung) or MTL (Mouth To Lung) vape. We tell you what these terms mean in our Guide To Vape Styles.

There’s also an RBA section available that can handle a resistance range of between 0.2 – 3.0ohm. So every style of vaping is possible to the budding coil builder.

The SMOANT ANT chip of the KNIGHT 80 makes it across so we can expect the same intelligent and reassuring vape experience.

Because some of the coils push the wattage limits of the device, a dual PCB chip structure has been employed to make efficient use of available power.

It’s not looking like there’s a TPD compliant edition since the pod has an e-liquid capacity of 3.5ml.

Expect to see the SMOANT KNIGHT 40 in four colour schemes. Gunmetal, Stainless Steel, Black and Rainbow (under review).

What’s In the Box?

• KNIGHT 40 device
• S6 mesh 1.1ohm coil
• Cartridge (coil adaptor and S4 mesh 0.35ohm coil installed)
• Type C USB charging cable
• Instruction manual
• Warranty card
• Certificated card

SMOANT KNIGHT 40 Pod Kit – Specifications

Device

• Dimensions: 84.5 x 42 x 23mm
• Weight: 33g
• Material: Zinc alloy + PCTG
• Battery: 1500mAh integrated
• Power output: 40W
• Screen: 0.42″ OLED
• Output mode: VW / DVW (best 0.3 – 3.0ohm)
• Voltage range: 3.2 – 4.2V
• Charging port: Type C
• Charging: 5V/1A
• Conversion rate: 95%

Pod

• Material: PCTG / Zinc alloy / Silicone
• Capacity: 3.5ml
• Coil: S1, S2, S3, S4, S5, S6, S-RBA

SMOANT KNIGHT 40 Pod Kit – Design and Build Quality

The Battery Section

Being made of Zinc Alloy the device is very light and surprisingly comfortable in the hand given the design. However, the fire button is located below the half way point so finger firing will be the most natural method.

However, finger firing will block the tiny 0.42″ screen. Something to consider, maybe.

One side of the battery section is tubular in design with the SMOANT logo running vertically down the spine.

No doubt this is the housing for the 1500mAh integrated battery.

The majority of the frame is comprised of clear PCTG and doesn’t match the frosted finish of the pod.

Leads, wires and circuitry are all clearly visible. I guess it looks kind of neat but at the same time has an unfinished quality about it.

I’m pleased that the Type C USB charging port has been side mounted. There’s enough width on the base of the battery section to allow the KNIGHT 40 to stand freely. It’s not going to tip over very easily.

The exterior of the pod housing is Zinc Alloy and spray coated with the colour scheme of choice. This also extends to the base of the device.

Speaking of the base it’s cool that SMOANT have included adequate battery venting.

The oval front panel is made from a glossy black PTCG. This is the business end of the device. Let’s take a look at functionality.

Quick Start Guide

How To Use the SMOANT KNIGHT 40 Pod Kit

• Press the fire button five times to turn the device on or off
• Press the fire button three times to select mode. Use the menu button to select mode.
• Modes are VW (variable Wattage), DVW and colour. Choose White, Red, Orange, Green or Blue. Press and hold the fire button to confirm selection
• Press the fire button and select button together to reset the puff counter

NB: The ANT chip will automatically detect the best wattage setting for the installed coil. I particularly like how coil parameters are briefly displayed on the screen when the pod is inserted.

Nice touch, SMOANT!

• While in standby, press the left or right side of the menu button to alter wattage
• Press the left and right side of the menu button to lock/unlock the device

While vaping, the display switches to vape duration in 0.1 second intervals.

Using DVW Mode

• When in DVW mode press the fire button and right side of menu button to enter the VW curve interface
• Press the left or right side of the menu button to alter vape duration between 0.5 – 2.0 seconds. Hold the fire button to move to the next curve setting.

This is SMOANT’S version of Variable Power Curve (VPC) in that the vape can have various stages of power. A soft to hard vape, a hard vape that tapers off or a vape that’s consistent throughout.

The Pod Section

It’s a bit different from the run of the mill pod and dare I say, a little on the ugly side. But that’s for good reason. Airflow adjustability has been built into the top.

Airflow skips across and down a sealed channel in the pod then hits the heated coil from beneath.

The 3.5ml pod is made from the same tough PCTG as part of the battery section and although frosted, e-liquid is clearly visible within.

Unfortunately that’s not the case when inserted into the battery section.

The mouthpiece is fixed and measures around 7mm in diameter. Not exactly conducive to a MTL vape, in my opinion. We shall see..

The airflow slider is workable enough, especially when using a finger nail for finer adjustments.

I did find the silicone stopper rather thin and awkward to remove, sitting directly beneath the airflow structure.

Fat fingers – does it every time! lol

The underside of the pod is entirely magnetic, making for excellent connectivity with the battery section.

How To Change A Coil and Fill The Pod

It’s important to note that the SMOANT S4 coil comes installed – with the coil adaptor already fitted.

You will need to remove this for use with all replacement coils. Follow the steps below..

• Remove the pod from the battery section
• Push the coil up inside the pod chamber ensuring a firm seal
• Lift the silicone fill tab from the side of the pod
• Gently pour e-liquid into the fill chamber making sure the level is above the cotton wicks

• Replace the silicone fill tab ensuring a snug seal
• Drop the pod back into the battery section

Let the E-liquid soak into the wicking ports for around five minutes prior to vaping.

How Does The SMOANT KNIGHT 40 Pod Kit Perform?

S4 0.35ohm mesh coil (Rated 30-35W)

The SMOANT ANT chip recognised the optimal setting as being 30W so that’s what I went with.

The e-liquid of choice was Black Rose Elixirs Carmilla, a Coffee beverage flavour set around a 50VG/50PG juice ratio with 20mg salt nicotine content.

Beginning with the airflow slot wide open I got a surprisingly powerful vape from the mesh coil and ramp up time was superb. The flavour pumped through as soon as the fire button was depressed.

This airflow setting created a semi restrictive lung hit and one I always favour. For a 50VG/50PG ratio, vapour production was around what I would expect. That’s to say I don’t recommend attempting to stealth vape with airflow wide open!

It’s by no means the quietest vape I’ve had from a pod kit but it’s still smooth and turbulence free.

The flavour was great. All the Coffee Liqueur notes were spilling from the exhale. There wasn’t quite enough power to do the spongey bakery elements enough justice and the cream was presented at around 50% its usual effectiveness.

But at this wattage I was more than satisfied with the resulting vape.

Further Airflow Restrictions

Adjusting the slider to mid position created that restrictive lung hit. It impressed me how little adjustment could make such a difference.

I did feel that the flavour was becoming a little muted, there being more sweetness to the beverage and less of the Coffee pulling through.

And a MTL vape is possible with even further restriction to the airflow. I don’t suggest closing it off entirely (although you can still vape) but allowing just a tickle of airflow.

You’ll need to be precise and patient but once found the option is there and it’s a decent vape. I got a good balance between flavour intensity and the sweeter aspect of the e-liquid.

70VG/30PG Blend

As much as I proved a 50VG/50PG ratio will work fine with the coil, it’s really better suited to thicker e-liquids because of the increased size of the wicking ports.

A 70VG/30PG blend is ideal. I wouldn’t suggest anything above this thickness, though.

When testing this ratio the flavour was just as good and you’ll obviously get more vapour production.

Extended inhales aren’t a problem for the coil and the additional heat (albeit limited) is most welcome, especially with bakery, spice or dessert based profiles.

S6 1.1ohm mesh coil (Rated 6-11W)

I used TEN TEN Red Berry Ice to test the MTL coil. It’s a 50VG/50PG juice ratio with 20mg salt nicotine already included. The SMOANT ANT chip suggested 10W as the optimal setting. Who am I to argue?

This may be a low powered coil but it still delivers a clout using the ANT chip recommended setting of 10W.

But with airflow wide open, you won’t get a very reliable MTL vape. It’s workable but it’s very loose.

Certainly not a comfortable experience and I found it more effective as a RDL vape.

The flavour was very good. The Menthol, Eucalyptus and Aniseed all pulled through nicely. Ok, not as intensely as the S4 coil for reasons of wattage constraints but I still thought this humble little chap was doing its utmost to please!

Further Airflow Restrictions

Adjusting the airflow slider to mid position made enough difference to push the inhale towards a half decent MTL vape. Still not exactly to my own preference but the Eucalyptus and Aniseed was beginning to leave more of a mark on the taste buds and lips.

The red berries were also more pronounced on this setting. Vapour production was good for that stealthy vape or four..

I closed the airflow right down to almost closed because the pod allows for such precise tuning. That’s where you’re going to find the best MTL vape. Because of the relatively wide bore of the mouthpiece I didn’t suffer the ‘stinging lips’ syndrome.

This left me to enjoy long, protracted vapes with plenty of flavour. It was a smooth, turbulence free draw and quiet enough for a few of those ‘bus stop’ moments.

Battery Performance and Charging

Using the 0.35ohm S4 coil I got 10.5 hours from a single battery charge. During this time I vaped around 7.5ml of E-liquid and notched up a total of 125 puffs.

The 1.1ohm S6 coil fared considerably better. I managed 27 hours of use, vaped 9ml of E-liquid and the number of puffs was 570.

However, fast Type C charging was a bit of a let down. It took 1 hour 45 minutes to revive an exhausted battery. The saving grace is that it’s possible to vape while charging.

I can’t say I noticed any degradation in performance as the battery level dropped. The flavour and vapour production was consistent throughout the life span of a charge.

Pros

• Fast ramp up time with either coil
• Great flavour from both coils
• Smooth turbulence free vape
• Versatile and effective airflow slider
• Charging in a vertical position
• Decent battery venting
• No leaking
• Light weight, slim and pocket friendly

Cons

• The small screen may be difficult to read (subjective)
• Unable to change screen colour (subjective to sample model)
• Ineffective DVW mode.
• Position of fire button (subjective)
• Unable to view remaining juice levels
• Silicone stopper can be difficult to use (subjective)
• Type C charging isn’t very fast

Final Review Verdict

I think I’m more impressed with the S6 MTL coil. The reason I say that is primarily down to economy of use. I got a whacking 27 hours use from a single charge. With airflow wide open, I was still able to pull a RDL vape.

Not its true role, granted but a welcome bonus nonetheless..

But that was the beauty of the airflow slider. Although quite small and limited, any adjustment was instantly noticeable. Given the distance is has to travel I found that quite impressive.

SMOANT have pretty much nailed airflow adjustability with the Knight 40 pod kit.

The speed of ramp up particularly impressed me with these mesh coils. Power was instant and power was consistent throughout use. I put that down to the efficiency of the ANT chip.

DVW mode seemed like a wasted opportunity. Whenever I made adjustments to test it, the bar chart would simply reset itself every time.

Not sure what that’s all about but it may be an issue with the sample. As a consequence I didn’t notice any difference with the power of the vape.

It’s also mentioned in the instructions that a choice of five screen colours are available. The option appears to have been omitted with the review sample.

When all’s said and done, the SMOANT KNIGHT 40 pod kit delivers the goods on flavour and vapour production. It’s reliable, light weight and pocket friendly and the coils were much more efficient than I was expecting.

Just before I sign off. I can confirm that the SMOANT Santi coils are compatible.

..I’m using the S2 0.6ohm RDL coil right now!

So one for the Christmas list? It’s certainly worthy of consideration.

The post SMOANT KNIGHT 40 Pod Kit Review – Coils With Clout appeared first on Ecigclick.

Smoant have been manufacturing vape gear for years and seem to now be mainly specialising in pod kits such as the Ant Bar Lafu, Charon Baby + and Veer.

What To Expect From The Smoant Vikii Pro?

The Vikii Pro pod kit is designed to be a budget friendly and easy to use starter kit.

As you can expect this is not going to be full of advanced options but it still provides plenty of features.

Inside the main device is a 700mAh battery which you recharge using a USB Type C cable at 0.5A in around 45-60 minutes.

The output is specified as 10W and seeing as there are only 2 coil resistances available this should be plenty.

To keep things simple there are no buttons or adjustments, the auto draw system will fire the device when you inhale on the mouthpiece.

This is designed to be small and light and also has a rubberised finish to help with grip and reduce fingerprints.

Included in the kit is the 1.2ohm pod, you can also buy the 1ohm pod separately.

The pods are refillable via the top fill port and will hold up to 3ml of your own e-liquid. If this is going to be available in TPD regulated areas the capacity will drop to 2ml.

There are 6 colour options to choose from: Silver, Gun-Metal, After-Rain, Sunset, Blue and Red.

Kit Includes

• Smoant Vikii Pro device
• 1.2ohm Vikii Pro pod
• USB Type C cable
• User manual

Smoant Vikii Pro Specs

• Size: 85.8x28x15.5mm
• Output: 10W (3.2-4.2V)
• Battery: 700mAh (internal)
• Display: LED indicator
• Resistance range: Not specified
• USB Type C port – 0.5A charge rate – 45 to 60 minutes charge time
• Pods: Refillable, fixed coils – 1ohm and 1.2ohm pods available
• Capacity: 3ml
• Top fill
• Auto draw

Sadly for me the original Vikii went way under my radar and we didn’t get to review it here either.

So I am unable to comment about how successful the original was. Let’s hope the Smoant Vikii Pro is a beauty! Let me know your thoughts in the comments below!

The post Smoant Vikii Pro Preview – Promising Purity? appeared first on Ecigclick.

Smoant have been a big player in the vape scene for quite a while now and popular kits include the Pasito, Pasito 2, Ladon, Knight 80 and Charon range.

What To Expect From The Smoant Ant Bar Lafu Pod Kit…

As mentioned above this is designed to be a simple and cost effective pod kit. Also this device might catch the eye of those using disposable vapes – as this is re-usable but still easy to get to grips with.

The reason this is so simple is the fact that the pods are pre-filled and are disposed of when the liquid chamber is empty. Another bonus to this style of pod is that you don’t have to faff about with changing coils or filling.

Inside the body is a 500mAh rechargeable battery which is charged in 30-45 minutes using the included USB Type C cable.

A breathing LED light is located on the base to display charge status and also ignites when vaping.

The pods have a 1.8ohm coil inside and come in a 2% Nicotine Salt strength.

So far there 10 flavours to choose from but there may be more in the future.

There are 5 colour options to choose from: Blue Violet, Space Grey, Dark Green, Turquoise and Pinky Blue.

Kit Includes

• Smoant Ant Bar Lafu device
• USB Type C cable
• User manual

Note the pre-filled pods are purchased separately in packs of 3.

Smoant Ant Bar Lafu Pod Kit Specs

• Size: 87x18x16mm
• Output: Not specified
• Battery:  500mAh (internal)
• Display: breathing LED Indicator
• Resistance range: Not specified
• E-liquid capacity: 3.5ml
• USB Type C port – 30-45 minutes charge time
• Pods: pre-filled, fixed coils
• 1.8ohm pods
• Pods available in 2% Nic Salt strength
• 1000 puffs life estimation

I love to see these simple and inexpensive devices – I really believe disposable vapers would be impressed with a kit like this and will save money and possibly the planet!

Let me know what you think of the Smoant Ant Bar Lafu Pod Kit in the comments below!

The post Smoant Ant Bar Lafu Pod Kit Preview – Bin The Disposables – Grab A “Re-usable”! appeared first on Ecigclick.

Smoant have a few versions of the Charon range including the Charon 218 TC Mod, Charon 218 TS and the Charon Mini 225W mod.

What To Expect From The Smoant Charon Baby + Kit…

The first thing that struck me about this kit – is that it is bigger than I was expecting – look at the photo below from the Smoant Facebook page…

But when you read the specs the size isn’t really that surprising as this one is packing a 1000mAh battery which is a great size for a pod kit.

Recharging is taken care of using the USB Type C port which you can charge at up to 1A charge rate. Smoant say you can charge this fully in 1 hour.

Output wise this will go up to 35W but it is not user controllable. Basically the “AI Smart ANT-Chip” senses the coil resistance and will adjust the output to suit.

The side panels are magnetic and replaceable and I show the full range of panels available further down in this preview.

An LED indicator is provided to view the battery charge remaining.

The pod has an airflow control lever too which is always welcome on a pod kit!

This uses the Santi S-Coil range which is compatible with the Santi kit.

You get the S-2 mesh 0.6ohm coil included in the kit but you can also purchase the S-1 0.4ohm Mesh or S-3 1.2ohm Mesh too.

The coils are removable and replaceable plus the pod is held into the device magnetically.

You can refill the pod with up to 3ml of your own e-liquid via the side fill port. I have not seen a mention of a 2ml TPD Compliant version as yet.

There are 6 base styles to choose from: Black Hannya, Black Tiger, Gunmetal Lion, Gunmetal Pan, Space Silver Yawata and Space Silver Dragon.

Plus you can customise this with the extra replaceable panels available…

Kit Includes

• Smoant Charon Baby + Device
• Pod
• S-2 Mesh 0.6ohm coil
• USB Type C Cable
• User manual

Smoant Charon Baby + Kit Specs

• Size: 22×45.6×79.4mm
• Output: 1-35W – auto adjusts output to suit coil installed
• Battery:  1000mAh (internal)
• Display: LED Indicator
• Resistance range: 0.3-3ohm
• Material: Zinc Alloy, PCTG
• E-liquid capacity: 3.5ml
• USB Type C port – 1A charge rate – 1 hour charge time
• Pods: Refillable, replaceable coil
• Coils: Smoant Santi S-coil range
• Auto draw operation
• Adjustable airflow
• Side fill port
• Replaceable magnetic side panels
• AI Smart Ant-Chip

This looks to be a fully featured (not so) little pod kit – it is a bit stingy to only include one coil though!

Let me know your thoughts on the Smoant Charon Baby + Kit in the comments below!

The post Smoant Charon Baby + Kit Preview – Makes Me Want To Shout “CHAARRONNNNNN” Like Ozzy! appeared first on Ecigclick.

Smoant of course are no strangers to a pod mod – with releases such as the Santi Kit, Pasito II, Pasito 1, and Knight 80 in their back catalogue.

What To Expect From The Smoant Veer Pod Kit…

As you can see the Veer has a more than slight resemblance to the Caliburn G – but this isn’t a bad thing as that is a very popular device.

Also like the Caliburn G this has replaceable coils – rather than a disposable refillable pod.

Even better than replaceable coils – are coils which are also compatible with other devices. The Veer uses the Smoant Baby Series of coils which are also used in the Battlestar Baby and Charon Baby kits.

Included in the kit are 2 coils which are wicked with Organic cotton:

• 0.6ohm Mesh
• 1.2ohm Ni80

The pod is refillable with up to 2.3ml of your own e-liquid via the pod side fill port.

By rotating the pod you have 2 airflow choices of a wider open (Direct To Lung – DTL) or more restricted (Mouth To Lung – MTL). We tell you what MTL and DTL mean in our Guide to Vape Styles.

Inside the mod you have a 750mAh internal battery which is recharged via the USB Type C port at up to 2A charge rate.

The output is specified as 10 / 15W – so I assume the mod automatically detects which coil is being used and selects the 10W for the 1.2ohm coil and 15W for the 0.6ohm.

An LED indicator is also provided to inform of battery capacity remaining.

There are 4 colour options to choose from: Saffron, Dark Green, Dark Black and Purple.

Kit Includes

• Smoant Veer Pod device
• Pod
• 0.6ohm Mesh coil (installed)
• 1.2ohm Ni80 coil
• USB Type C Cable
• User manual

Smoant Veer Pod Kit Specs

• Size: 114×22.5×12.4mm
• Output: 10/15W
• Battery:  750mAh (internal)
• Display: LED Indicator
• Resistance range: 0.5-.ohm
• Material: Aluminium Alloy, PCTG
• E-liquid capacity: 2.3ml
• USB Type C port – 2A charge rate
• Pods: Refillable, replaceable coil
• Coils: Smoant Baby Coil range (Charon Baby, Battlestar Baby)
• 2 airflow settings
• Side fill pod

Although the looks are very familiar I do hope the performance is too!

Let me know what you think of the Smoant Veer Pod Kit in the comments below!

The post Smoant Veer Pod Kit Preview – Smoant Veer Towards The Caliburn? appeared first on Ecigclick.

For those suffering from “Pod Fatigue” I will quickly run down the features of this kit for you!

What To Expect From The Smoant Santi Kit?

Inside the mod is a 1100mAh battery which is charged via the USB Type C cable – but the charging rate / time are not specified.

The output is adjustable from 1-40W and you can view your vaping data on the colour 0.96in TFT Screen. You can also change the screen theme colours.

Controlling the device is the upgraded ANT chip which is similar to that found in the Knight 80 and Pasito kits.

The mod body is made from Zinc Alloy and PCTG plastic which Smoant say is wear resistant and fingerprint proof.

An airflow adjustment slide switch is located on the side to adjust the airflow to your preference.

The pod is removable and is refillable via the side fill port with up to 3.5ml (or 2ml in TPD regulated areas) of your own e-liquid.

A new range of coils has been created for this kit. The mesh coils use an ERNiCrMo metal – which is a Nickel-Chromium-Molybdenum wire which apparently gives purer flavour and longer coil life.

• S-1 DL (Direct Lung) – 0.4ohm Mesh
• S-2 RDL (Restricted Direct To Lung) – 0.6ohm Mesh (included in kit)
• S-3 MTL (Mouth To Lung) – 1.2ohm Mesh
• S-RBA (DL, RDL / MTL) – you build this with your own coil to suit your vaping style.

If these abbreviations are making you scratch your head read our Guide To Vape Styles.

There are 4 colours to choose from: Gunmetal, Stainless Steel, Full Black and Rainbow.

Kit Includes

• Smoant Santi device
• Cartridge
• S-2 0.6ohm coil (installed)
• USB Type C Cable
• User manual

Smoant Santi Kit Specs

• Size: 104x28x18.5mm
• Output: 1-40W (3.2-4.2V)
• Battery: 1100mAh (internal)
• Display: 0.96in TFT colour screen
• Resistance limits: 0.3-3ohm
• E-liquid capacity: 3.5ml (standard) / 2ml (TPD)
• USB Type C Charging
• Pods: Refillable, removable coil pods
• Coils: S-1, S-2, S-3 or RBA
• Adjustable airflow
• 5 screen theme colours
• Side fill port
• ANT chipset

This looks like a great kit – I think including only one coil is a bit stingy though!

What do you think of the Smoant Santi Kit? Tell me in the comments below!

The post Smoant Santi Kit Preview – Santi Claus Is Coming To Town… appeared first on Ecigclick.

I reviewed the original Pasito and found it to be a lovely kit – so how have Smoant updated it?

What Is New On The Smoant Pasito II Pod Kit?

The Pasito 2 has had a lot of updates and it is now a real grown up pod kit full of features.

Looking first at the device itself – this has an internal 2500mAh battery which is charged via the USB Type C port at a fast 2A rate.

The output is higher too at 1-80W and you can choose from Variable Wattage, DVW (I assume “Dynamic” Variable Wattage?), Bypass, Temperature Control and TCR.

A 0.96in colour TFT screen is located on the side and the screen colour themes can be changed.

The pod has changed too and now is compatible with 7 different coil types.

Firstly the K range of coils which were found on the Smoant Knight 80 kit plus some new coils too:

• K3 – 0.6ohm Mesh
• K2 – 0.4ohm Dual Mesh
• K-RBA – DIY RBA coil
• K1 – 0.3ohm Mesh

Plus if you purchase the optional Pasito 2 adaptor you can use the coils from the original Pasito which include the 1.4ohm Ni80, 0.6ohm Mesh and the Pasito RBA.

The pod capacity has now increased to 6ml however this is still only going to be 2ml in TPD regulated areas.

You can also purchase a 510 adaptor to allow any 510 atomiser to be used on the device – basically turning it into a box mod.

An airflow adjustment lever is located on the top of the pod.

There are 4 colours to choose from: Carbon Fibre, Chocolate, Diamond Shaped and Indigo.

Kit Includes

• Smoant Pasito II device
• Pod
• K-1 0.3ohm mesh coil (installed)
• K3 0.6ohm mesh coil
• Type C USB cable
• User manual

Smoant Pasito II Kit Specs

• Size: 117x38x27mm
• Output: 1-80W
• User modes: VW, DVW, Bypass, TC (Ni, Ti, SS316), TCR
• Battery: 2500mAh (internal)
• Display: 0.96in colour TFT screen
• E-liquid capacity: 6ml (Standard) / 2ml (TPD)
• Pods: Refillable, replaceable coil
• Coil options: Compatible with Smoant Knight coil range and Original Pasito coils (adaptor available separately) – RBA available in both coil ranges
• Adjustable airflow
• Side fill port
• 510 adaptor available separately to use device as a box mod
• Type C USB – 2A charge rate

I love the look of this kit – even more features and lots of coil options too including 2 types of RBA!

Will you be purchasing the Smoant Pasito II Pod Kit? Let me know in the comments below!

The post Smoant Pasito II Pod Kit Preview – The Pasito Grows Up! appeared first on Ecigclick.